DIY: Sequin Bracelet ..by Erica all the way from “Honestly …WTF”

Leave a comment

After purchasing an abundant (and unnecessary) amount of sequins for last week’s tutorial, I mulled over ways to repurpose them into another project. Inspired by those beautiful African necklaces made from recycled vinyl, it was obvious that a bracelet DIY was in order. Simple and fast . . . I dare you not to make just one!

You’ll need:

 

Cut 12 inches of elastic cord and tie a double knot at the end.

There’s a quick and easy shortcut for adding sequins rather than threading them on one at a time. Pull a bunch of sequins off the strand. Keep the sequins in place between the pads of the index finger and thumb. Thread the elastic cord through the sequins.

Continue stringing on sequins, in any pattern, using the same method.

Wrap the strung sequins around the wrist to check for size – remember to account for the bracelet stretching. Knot the elastic cord into a double knot and pull tightly to tighten. Trim the ends.

Cut the embroidery floss into a few 2 inch pieces. Fold them in half over the knot. Take another 2 inch strand and tie the floss together into a double knot at the top.

Trim the ends. Use a needle to comb through and unravel the floss. Trim the tassel.

And that’s it! *Note: I prefer using flat sequins versus faceted sequins for this particular tutorial.

Stack, stack away . . .

Advertisements

Ladies all the way!

Leave a comment

Printed Clutches!


Leave a comment

hey hey hey!!!!!…yea..its been soooo long though…yea, i know…India has been draining my time and energy..

well well…so urmm…today..am gonna be focusing on the ladies..ionno why though..but during the time i was gone..more of ladies than men were really concerned….so ladies..this is ur space!

Currently coveting: Side Striped trousers.

Denim & Color Chain

Amazing Artwork

Leave a comment

Amazing Artwork Painted On Nude Models

Realistic landscapes, detailed paintings of animals, and emotionally charged abstract artwork? *snore* Nekkid ladies? Where? Under the the paint? Oh snap! Why didn’t you say so in the first place? Artist Craig Tracy paints beautiful artwork on top of human canvases (aka nude models) creating breathtaking living artwork. At first glance it can be difficult to spot the person in the painting, but upon careful inspection their form becomes apparent. Tracy says that most paintings usually take about a full day to complete and that none of his work is ‘shopped.

40 Cool Kids And Teen Room Design Ideas From Asdara

Leave a comment

A Spanish furniture company called Asara has presented their new catalog recently. It consists of furniture for kids and teen rooms and features plenty of cool ideas how to design a room for your children. Their furniture and design solutions can solve space problems and help to create a practical and beautiful living and studying environment for your young ones. On Asdara’s company website you can find out more about their products and how to buy them. For those who are searching for more cool kids room design ideas we have several roundups of shared rooms, cute girl bedrooms and stylish boy rooms.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DIY again [Specially for the Laides]

3 Comments

DIY Embellished Friendship Bracelets

so i found out that girls wanted something of theirs…alone..well

This is from a friend, Claire.

Enjoy…

The weather is warming up and my wrists are feeling rather lonely and bare after hiding under long sleeves all season long. But after digging up last year’s DIY friendship bracelets, I realized they desperately needed sparkly and shiny upgrades. Today we’re showing you three easy ways to embellish your friendship bracelets, making them all grown up . . .

To add rhinestones, you’ll need:

  • a chevron friendship bracelet (tutorial found here)
  • 5-6” crystal rhinestone chain (last used here)
  • 1 yard of embroidery floss
  • an embroidery needle
  • a pair of scissors

 

Thread the needle with embroidery floss and tie the end into a double knot. Push the needle through the back of bracelet. Lay the rhinestone chain along the middle of the bracelet, using the chevron pattern as a guide.

Stitch the floss between the first two rhinestone links, pushing needle out the middle of the bracelet. Bring the needle back through the middle, this time further down between the second and third links.

Continue stitching between the rhinestone links. After the very last stitch, tie a double knot on the backside and trim the ends.

Your friendship bracelet is sparkling and finished!

To add studs, you’ll need:

  • a chevron friendship bracelet (tutorial found here)
  • 5 3/8” brass cone studs (last used here)
  • a pair of small, sharp scissors
  • a screwdriver

Use a Sharpie or marker to make 5 evenly spaced marks along the middle of the friendship bracelet. From the backside, push the point of the scissors through the mark to create a hole.

Push a screw through the hole. Twist the coned spike onto the screw and use a screwdriver to tighten.

Repeat the steps with the rest of the spikes. Voila! Your friendship bracelet has a spiked spine.

To add chain, you’ll need:

  • a friendship bracelet (tutorial found here)
  • 5-6” of brass curb chain
  • 1 yard of embroidery floss
  • an embroidery needle
  • a pair of scissors

Thread the needle with embroidery floss. Untie one end of the friendship bracelet and re-knot it with the tail of the threaded embroidery floss. Push the needle through the outer edge of the backside of the bracelet.

Lay the chain flat, against the edge of the bracelet. Thread the needle over and through the first link. Push the needle though the backside about two rows down. Depending on the width of each link, the row count may vary.

Keep stitching. Make two stitches around the last link, untie the knot and re-knot with the last of the floss. Trim away any excess.

Your chain trimmed friendship bracelet now has an edge – how simple was that?

Stack ‘em, give ‘em away and you’re officially ready for summer.

DIY!!!! at last :D

Leave a comment

DIY Beaded Button Down Shirt

I immediately did a double take after spotting this shirt with baubles stitched down the “placket,” which I just recently learned is the term used to describe the middle section of a button down shirt. Honestly? Placket?! In any case, it’s an easy DIY and the most brilliant way to add a bit of texture and pizazz to any shirt!

You’ll need:

  • a button down shirt
  • a mix of metal, plastic or glass beads
  • a needle fine enough to fit through the beads
  • thread

Keep the shirt buttoned. Thread the needle with about a yard of thread and tie the ends into a double knot. Push the needle through the backside of the middle of the placket.

Slide a bead onto the needle and bring the needle back through the fabric on the other side of the bead. Continue sewing beads onto the fabric using this running stitch.

After adding 5-6 beads, secure the stitch by tying off the thread with a double knot. This helps reinforce the stitch, especially with the weight of the beads. If the thread is long enough, continue to stitch on another group of beads. If the thread runs out, go ahead and cut the thread and start again with the first step.

Continue adding beads in small groups along the placket.

Stop 3/4 of the way down.

Finished!! xx

Older Entries